Engbo MAXI 34-series Specifications download pdf (Page 10)

SP Windlass Control Unit v1.0.0 2015

Troubleshooting

If the windlass still does not work normally after you have tried these procedures, the fault is in the windlass itself. Contact

your nearest dealer.

FAULT SYMPTOM FAULT CODES/STATUS SOLUTION

Windlass does not operate "Power"LEDnotlit Check:

Mainswitch/breakerisengaged.

Checkbatteryfuses.

Visuallyinspectcablesandverifythatterminalsaretight.

Measurebatteryvoltage.

"Power"LEDlit Turnonpanel/remotecontrol(seeusermanual)

Seebelow:

Windlass only runs for 0,5 seconds

when pressing "IN"

None Checkcontrolpanelconnections.Signalsfor"IN"and"OUT"mightbe

swapped.

When pressing "OUT" free fall is not

engaged.

Or: When pressing "IN", motor is

running but gypsy is not turning

None SwapmotorcablesD1andD2onthecontrolunit

Windlass has poor performance “Lowvoltage” Voltagehasdroppedbelow9V

Checkbatteries.

None Measurebatteryvoltagewhileoperatingthewindlass.Ivoltagemeasure

below11V/22V,allowbatteriestocharge.

Ifthebatteryvoltageisacceptable,measurevoltageonthemotortermi-

nals,cablevoltagedropshouldbelessthan1Vwhenmotorisrunning.

Windlass releases anchor, but do

not wind in

None Checkthatendstopsensorisnotactive(Indicatedby"EndStop"LEDon

controlunitorLEDbuiltintothesensor.)

Checksensorconnectionsonthecontrolunit.

SensorLEDshouldnotbelitifnometalobjectispresentinfrontofit.

Windlass wind past endstop None Checkthattheendstopwirewoundaroundtheropeisintact.Pulltherope

withendstopwireovertheendstopsensorandverifythat(«EndStop»LED

lightup)

Adjustsensorclosertotheropeifneccesary.

Windlass releases anchor, but stops

immediatly when pressing "IN"

Noneor“Lowvoltage” Ifthebatteryisinpoorconditionitmightmeasure12/24Vwhenwindlass

isnotinuseandstillexperinceasignicantvoltagedropwhenthemotor

starts(suchvoltagedipsmightbediffculttomeasure)Thistypeofvoltage

dropscanleadtofalsetriggeringoftheendstopsensor.

Windlass stops during operation “MotorOverload” Currentlimitationhastriggered.

Thismeansthatthewindlassisoverloaded.Tryagainwithreducedload.

Ifthisfaultistriggeredwhilethewindlassislightlyloaded,itmightindicate

amechanicalfailure.

“ControllerOvertemp” Thecontrolunittemperaturesensoristoowarm.

Letthecontrollercooldown,andtryagain.

“MotorOvertemp” Themotoristoohot.

Thewindlasscontrollercalculatesmotortemperaturedependingonload

anruntime.

Letthewindlasscooldown.

“ControllerOverload” Thisfaultindicatesthattheinternalprotectionofthecontrrollerhastrig-

gered.Thiscanbecausedbyexccessivesurroundingtemperatureandhigh

load

“RuntimeExceeded” Signal"OUT"or"IN"havebeencontinuousformorethan5minutes.Thisis

aprotectionagainstpossiblefaultycontrolsignals.Re-activationispossible.

Abnormal noise during operation Thewindlassmustbeserviced.

Windlass operates, but rope is not

wound in

Theropecanslipinthegypsyifthewindlassismountedincorrectly.

Anchor is not released Theanchormightnotreleasefromthebracketifmountedincorrectly.

Note! Main switch/braker must be disconnected whenever working on the windlass mechanical parts

1 2 ... 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Engbo MAXI 34-series Specifications Page 10

Comments to this Manuals

Related products and manuals for Unknown Engbo MAXI 34-series